Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
In this article in the next paragraph you might get some incredibly good data with regards to Tools You Need to Install a New Bathtub .
Mounting a bath tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old bathtub is easily accessible, the task can relocate rapidly; if you have to open a wall surface to eliminate the old bathtub as well as position the new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the new one. See to it you have actually qualified yourself for the work and also are comfortable attempting it. As opposed to working with a contractor to take control of a halfway-completed project, it is far better to take into consideration utilizing one before you start. Possibilities are you may require a specialist plumber to make tube connections.
This article will certainly assist you set up a new bathtub in your bathroom if you have actually currently purchased a new bathtub and also don't require to alter the arrangement of your previous water supply pipelines.
Your tools and product checklist should consist of the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be rather problematic as a result of the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this process. When the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washers are in area between the tap as well as the sink. Safeguard the faucet in position with the producer supplied backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical tap ports. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub until the level reads degree.
To set up taps, fit all-time low of the furthest adaptable faucet connector to the proper supply pipe by making a compression join; after that do the exact same for the various other tap.
Activate the supply of water and also check all joints and also brand-new pipework for leakages and tighten them if needed. Load the bathtub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the tub needs to wait up until the tub has actually been used a minimum of when as this will settle it into its final setting.
Planning for the Installment
To start with, the supporting frame supplied with the bathroom must be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final position.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and the tiling, bring about problems with wetness as well as possible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill the tub with water before securing, to allow for the motion experienced when the tub is in usage. The sealer can split fairly very early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily offered on the market. It is a good idea to fit the floor tiles using waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about A Step-by-Step Guide to Installing a Bathtub? Try leaving feedback down below. We'd be delighted to know your responses about this blog posting. In hopes that you visit us again later on. If you please take the time to distribute this entry if you enjoyed it. We thank you for reading our article about Installing A Bathtub.
Source This Article
Report this page